[1]    F. Yang, L. Peng and K. Okazaki, Microindentation of aluminum, Met. Mat. Trans. 35A (2004), 3323-2338.

[2]    S. Ping Wu, D. R. Liu, J. J. Guo, Y. Q. Su and H. Z. Fu, Influence of process parameters on CET in Ti-Al alloy ingot with consideration of shrinkage cavity formation: a computer simulation, J. Alloys Comp. 441 (2007), 267-277.

[3]    R. W. Osório, L. C. Peixoto, M. V. Canté and A. Garcia, Microstructure features affecting mechanical properties and corrosion behavior of a hypoeutectic Al-Ni alloy, Mater. Design 31 (2010), 4485-4489.

[4]    P. R. Goulart, J. E. Spinelli, W. R. Osório and A. Garcia, Mat. Sci. Eng. A 421 (2006), 245-253.

[5]    M. Gögebakan, O. Uzun, T. Karaaslan and M. Keskin, Rapidly solidified Al-6.5 wt.% Ni alloy, J. Mat. Proc. Tech. 142 (2003), 87-92.

[6]    I. S. Jung, M. C. Kim, J. H. Lee, M. H. Oh and D. M. Wee, High temperature phase equilibria near Ti-50 at.% Al composition in Ti-Al system studied by directional solidification, Intermetallics 7 (1999), 1247-1253.

[7]    H. Kaya, M. Gündüz, E. Çadırlı and O. Uzun, Effect of growth rate and lamellar spacing on microhardness in the directionally solidified Pb-Cd, Sn-Zn and Bi-Cd eutectic alloys, J. Mat. Sci. 39 (2004), 6571-6576.

[8]    H. Kaya, E. Çadırlı, M. Gündüz and A. Ülgen, Effect of the temperature gradient, growth rate and the interflake spacing on the microhardness in the directionally solidified Al-Si eutectic alloy, J. Mat. Eng. Perf. 12 (2003), 544-551.

[9]    H. Kaya, E. Çadırlı, U. Böyük and N. MaraÅŸlı, Variation of microindentation hardness with solidification and microstructure parameters in the Al based alloys, Appl. Surf. Sci. 255 (2008), 3071-3078.

[10]    S. Engin, U. Böyük, H. Kaya and N. MaraÅŸlı, Directional solidification and physical properties measurements of the zinc-aluminum eutectic alloy, Int. J. Min. Met. Mater. 18(6) (2011), 659-664.

[11]    A. E. Aresa, S. F. Gueijmanb, R. Caramc and C. E. Schvezov, Analysis of solidification parameters during solidification of lead and aluminum base alloys, J. Cryst. Growth 275 (2005), 319-327.

[12]    U. Böyük, N. MaraÅŸlı, E. Çadırlı, H. Kaya and K. KÅŸlioÄŸlu, Variations of microhardness with solidification parameters and electrical, resistivity with temperature for Al-Cu-Ag eutectic alloy, Current Appl. Phys. 12 (2012), 7-10.

[13]    K. A. Jackson and J. D. Hunt, Lamellar and rod eutectic growth, Trans. Metal. Soc. A.I.M.E. 236 (1966), 1129-1142.

[14]    A. Ourdjini, J. Liu and R. Elliott, Eutectic spacing selection in the Al-Cu system, Mater. Sci. Tech.-Lond. 10 (1994), 312-318.

[15]    H. Kaya, E. Çadırlı and M. Gündüz, Eutectic growth of unidirectionally solidified bismuth-cadmium alloy, J. Mat. Proc. Tech. 183 (2007), 310-320.

[16]    H. Kaya, E. Çadırlı and M. Gündüz, Effect of growth rates and temperature gradients on the spacing and undercooling in the broken-lamellar eutectic growth (Sn-Zn eutectic system), J. Mat. Eng. Perf. 12(4) (2003), 456-469.

[17]    J. Fan, X. Li, Y. Su, J. Guo and H. Fu, Dependency of microhardness on solidification processing parameters and microstructure characteristics in the directionally solidified Ti-46Al-0.5W-0.5Si alloy, J. Alloys Comp. 504 (2010), 60-64.

[18]    M. Åžahin and H. Kaya, Mechanical properties of directionally, solidified lead-antimony alloys, I. J. Min. Met. Mat. 18(5) (2011), 582-588.

[19]    A. Sergeev and V. Mitin, Electron-phonon interaction in disordered conductors: static and vibrating scattering potentials, Phys. Rev. B 61 (2000), 6041-6047.

[20]    Z. Boekelheide, D. W. Cooke, E. Helgren and F. Hellman, Resonant impurity scattering and electron-phonon scattering in the electrical resistivity of Cr thin films, Phys. Rev. B 80 (2009), 134426-134438.

[21]    V. Rudnev, D. Loveless, R. Cook and M. Black, Handbook of Induction Heating, Marcel Dekker Inc., New York, 2003, p. 119.

[22]    R. Hultgren, R. L. Orr, P. D. Anderson and K. K. Kelley, Selected Values of Thermodynamic Properties of Metals and Alloys, University of California, Wiley, Berkeley, 1963, pp. 318-322.