| Title | Cited by | Year |
|---|---|---|
EXCHANGE COUPLED NANOCOMPOSITE HARD MAGNETIC ALLOYS I Betancourt, HA DaviesInternational Journal of Materials Engineering and Technology 1 (1), 53 - 92, 2009 |
69 | 2009 |
FINITE DIFFERENCE ALGORITHM FOR TRANSIENT MAGNETO-THERMO-ELASTIC STRESSES IN A NON-HOMOGENEOUS SOLID CYLINDER MA FahmyInternational Journal of Materials Engineering and Technology 3 (1), 87 - 93, 2010 |
12 | 2010 |
AN EXPLORATORY STUDY ON ALKALI-ACTIVATED SLAG PASTE BLENDED WITH MICRO METAKAOLIN SUBJECTED TO THERMAL LOADS AM Rashad, KM ShokryInternational Journal of Materials Engineering and Technology 13 (2), 187 - 217, 2015 |
8 | 2015 |
SUPPRESSED HYDROGEN SOLUBILITY IN BODY CENTRED CUBIC Va-GROUP METAL (Nb AND Ta) BY ALLOYING WITH W OR Ru ANALYSED ON THE BASIS OF STATISTICAL THERMODYNAMICS N ShohojiInternational Journal of Materials Engineering and Technology 7 (1), 33 - 54, 2012 |
8 | 2012 |
FRICTIONAL BEHAVIOR BETWEEN PISTON RING AND CYLINDER LINER IN ENGINE CONDITION WITH APPLICATION OF RECIPROCATING TEST M Çakir, IH AkçayInternational Journal of Materials Engineering and Technology 11 (1), 57 - 71, 2014 |
7 | 2014 |
INFLUENCE OF THE GROWTH RATE ON PHYSICAL PROPERTIES IN THE ALUMINUM-ANTIMONY EUTECTIC ALLOY A Aker, S Engin, I Yilmazer, H KayaInternational Journal of Materials Engineering and Technology 9 (1), 59 - 76, 2013 |
7 | 2013 |
ONE-STEP SYNTHESIS OF SILVER NANOPARTICLES USING LOW MOLECULAR WEIGHT COMPOUNDS AT ROOM TEMPERATURE T Natsuki, J NatsukiInternational Journal of Materials Engineering and Technology 13 (1), 109 - 119, 2015 |
6 | 2015 |
A STUDY OF Ni-Cr-Si-BASED THIN FILM RESISTORS PREPARED BY DC MAGNETRON SPUTTERING DJ Feng, YC Lee, YB ChenInternational Journal of Materials Engineering and Technology 11 (2), 149 - 164, 2014 |
6 | 2014 |
SWCNTs/POLY(ETHYLENE TEREPHTHALATE GLYCOL-MODIFIED) (PETG) NANOCOMPOSITES: PREPARATION AND CHARACTERIZATION OF THIN CONDUCTIVE FILMS S Paszkiewicz, I Pawelec, A Szymczyk, Z RoslaniecInternational Journal of Materials Engineering and Technology 11 (2), 139 - 148, 2014 |
6 | 2014 |
COKE FORMATION QUANTITATIVE ANALYSIS ON IMPREGNATED AND SOL-GEL CATALYSTS APPLIED IN THE DRY REFORM OF METHANE G Gonçalves, LMS Colpini, R Menechini Neto, OAA Santos, LMMJ a, ...International Journal of Materials Engineering and Technology 10 (1), 45 - 65, 2013 |
6 | 2013 |
DESIGN OF A FLANGED RING PRODUCED BY HOT FORMING USING FE ANALYSIS M Monti, G BertiInternational Journal of Materials Engineering and Technology 7 (1), 1 - 15, 2012 |
6 | 2012 |
DEVELOPMENT OF CRANIAL IMPLANT THROUGH INCREMENTAL SHEET FORMING FOR MEDICAL ORTHOPEDIC APPLICATIONS J Castelan, A Daleffe, L Schaeffer, J Casagrande, V Gruber, D FritzenInternational Journal of Materials Engineering and Technology 4 (1), 63 - 80, 2010 |
6 | 2010 |
HAZ CHARACTERIZATION OF GTD-111 NICKEL BASED SUPERALLOY WELDING AR Said, J Syarif, Z SajuriInternational Journal of Materials Engineering and Technology 2 (2), 133 - 139, 2009 |
5 | 2009 |
ELECTRICAL CONDUCTION AND DIELECTRIC PROPERTIES OF THE LACUNAR SYSTEM N Chihaoui, M Bejar, E Dhahri, MA Valente, LC Costa, MPF GraçaInternational Journal of Materials Engineering and Technology 13 (2), 129 - 146, 2015 |
5 | 2015 |
EXPERIMENTAL INVESTIGATION OF THE HOLE EXPANSION CAPABILITY OF A MARTENSITIC AHSS STEEL WITH TWO PUNCH GEOMETRIES AND A VARIETY OF HOLE DIAMETERS LA Thesing, U Boff, L SchaefferInternational Journal of Materials Engineering and Technology 15 (2-3), 159 …, 2016 |
5 | 2016 |
TEMPERATURE AND PH-DEPENDENT MOLECULAR DYNAMICS OF Thermoplasma acidophilum TETRAETHER LIPID MEMBRANE IN A COMPUTER-SIMULATED MODEL Z Luthfa, HJ Freisleben, R SalehInternational Journal of Materials Engineering and Technology 13 (2), 161 - 185, 2015 |
5 | 2015 |
EFFECT OF WELDING PROCESSES AND POSTWELD HEAT TREATMENT ON THE MECHANICAL PROPERTIES OF Ti-6AL-4V CASTINGS R Reda, AH Hussein, A Nofal, M Sobih, ESM El-BannaInternational Journal of Materials Engineering and Technology 13 (1), 1 - 21, 2015 |
4 | 2015 |
MORPHOLOGY AND QUANTITY OF GAS POROSITY AS THE RESULT OF DURALUMIN CAST ON REVEBERATORY FURNACE W Suprapto, B Suharno, JW Sudarsono, D PriadiInternational Journal of Materials Engineering and Technology 8 (2), 123 - 135, 2012 |
4 | 2012 |
AN ELIMINATION OF DISPERSE RED 167 FROM A TEXTILE DYE EFFLUENT WITH NATURAL HYDROXYAPATITE W Lemlikchi, P Sharrock, MO Mecherri, M FialloInternational Journal of Materials Engineering and Technology 6 (2), 111 - 124, 2011 |
4 | 2011 |
INTEGRITY ASSESSMENT OF NOTCHED BARS SUBJECTED TO ELASTIC-PLASTIC-CREEP DAMAGE EMPLOYING MULTIAXIAL STRESS/STRAIN FIELDS K Zarrabi, J JelwanInternational Journal of Materials Engineering and Technology 3 (2), 173 - 187, 2010 |
4 | 2010 |
AN EVALUATION OF RAPID MANUFACTURED CELLULAR STRUCTURES TO ENHANCE INJECTION MOULDING TOOL PERFORMANCE M Dotcheva, D Thomas, H MillwardInternational Journal of Materials Engineering and Technology 1 (2), 105 - 127, 2009 |
4 | 2009 |
A NEW APPROACH FOR EVALUATING THE PEDALLING EFFICIENCY OF A BIKE RIDER IN SEATED CYCLING BY USING THEORY OF ENGINEERING MECHANICS CC Wu, D BallanceInternational Journal of Materials Engineering and Technology 14 (2), 115 - 150, 2015 |
3 | 2015 |
DYNAMIC ADSORPTION OF FROM FLOWING AIRSTREAMS ON ACTIVATED TEDA CHARCOAL JC Wren, CJ Moore, Z QinInternational Journal of Materials Engineering and Technology 3 (1), 1 - 32, 2010 |
3 | 2010 |
THE RELATION OF CRACK LENGTH AND OVERLOADS TO CRACK GROWTH ON SOLID ROUND BAR A Purnowidodo, B PrawaraInternational Journal of Materials Engineering and Technology 5 (1), 29 - 40, 2011 |
3 | 2011 |
MULTIVARIABLE REGRESSION ANALYSIS OF OPTIMAL CONDITIONS FOR A PHYSICS-CHEMICAL PROCESS VA Rusanov, SV Agafonov, AV Daneev, SV LyaminInternational Journal of Materials Engineering and Technology 10 (1), 19 - 44, 2013 |
3 | 2013 |
DYNAMIC STABILITY AND FREE VIBRATION OF MULTI-SPAN FLUID-CONVEYING PIPES JS Wu, SC Lo, RM ChaoInternational Journal of Materials Engineering and Technology 14 (1), 1 - 43, 2015 |
3 | 2015 |
PHYSICAL PROPERTIES OF TITANIUM-DOPED ZINC OXIDE THIN SOLID FILMS GROWN BY SOL-GEL METHOD L Castañeda, M Avendaño-Alejo, C Márquéz-Beltran, A MaldonadoInternational Journal of Materials Engineering and Technology 4 (2), 147 - 159, 2010 |
3 | 2010 |
COMPATIBILITY OF BIDZAR LIMESTONE AND FIGUIL CLAY (NORTHERN CAMEROON) FOR THE PRODUCTION OF PORTLAND CLINKER E Yamb, BN Bayiha, N Billong, SI RobertovnaInternational Journal of Materials Engineering and Technology 15 (1), 63 - 73, 2016 |
3 | 2016 |
CT-BASED RECONSTRUCTION OF METAL FOAM COMPOSITE MATERIAL REINFORCED WITH CERAMIC SPHERICAL SHELL STRUCTURE I Kozma, I Zsoldos, G Dorogi, S PappInternational Journal of Materials Engineering and Technology 15 (2-3), 93 - 107, 2016 |
3 | 2016 |
DETERMINATION OF PROPERTIES AND QUALITY OF GLASS FIBER REINFORCED POLYMER COMPOSITE REINFORCING BARS P Arczewska, MA Polak, A PenlidisInternational Journal of Materials Engineering and Technology 15 (4), 225 - 261, 2016 |
3 | 2016 |
EXPERIMENTAL STUDY OF A PARABOLIC SOLAR CONCENTRATOR WITH OPTIMIZED BACK AXIAL DISTANCE OF THE FOCAL POINT S Modibo, T Siaka, D Soro, D Idrissa, B MarÃInternational Journal of Materials Engineering and Technology 18 (1), 17 - 40, 2019 |
3 | 2019 |
CONTROLLED ZnO DEPOSITS FOR GAS SENSORS P YobouÃ, P Kouakou, A KamagatÃ, PMÃ nini, F Mesnilgrente, ...International Journal of Materials Engineering and Technology 18 (2), 55 - 66, 2019 |
3 | 2019 |
PROPOSING DESIGN GUIDELINE FOR HYDROGEN PERMEATION MEMBRANE ALLOY BASED ON Va-GROUP METALS (V, Nb AND Ta) TAKING INTO ACCOUNT ATOMIC INTERACTION ENERGY PARAMETER EVALUATED … N ShohojiInternational Journal of Materials Engineering and Technology 15 (1), 75 - 92, 2016 |
3 | 2016 |
AGGREGATION MODELING USING SINC METHODS OF SOLUTION TO THE STIELTJES FORMULATION OF THE POPULATION BALANCE EQUATION F Stenger, TA RingInternational Journal of Materials Engineering and Technology 9 (2), 77 - 87, 2013 |
2 | 2013 |
WINGEARS: A SOFTWARE TOOL FOR CHECK AND DESIGN OF BEVEL GEAR S Chayoukhi, K Mehdi, A ZghalInternational Journal of Materials Engineering and Technology 1 (1), 93 - 103, 2009 |
2 | 2009 |
GENETIC ALGORITHM APPROACH TO OPTIMIZE THE PROCESS PARAMETERS IN ROLLER BURNISHING OPERATION KD Raju, KE PrasadInternational Journal of Materials Engineering and Technology 2 (2), 177 - 205, 2009 |
2 | 2009 |
EFFECT OF PROCESS PARAMETERS ON GAP CURRENT IN WEDM H Singh, R GargInternational Journal of Materials Engineering and Technology 3 (1), 95 - 106, 2010 |
2 | 2010 |
FATIGUE AND TENSILE PROPERTIES OF TITANIUM BASED BULK GLASSY ALLOYS M Okayasu, S Takasu, T Bitoh, DH Shin, M MakabeInternational Journal of Materials Engineering and Technology 5 (2), 77 - 90, 2011 |
2 | 2011 |
NUMERICAL SIMULATION OF THE SWAGE TUBE FORMING (STF) IN CYLINDERS H Barbachano, JM Alegre, II CuestaInternational Journal of Materials Engineering and Technology 7 (2), 71 - 91, 2012 |
2 | 2012 |
FORCES IN END MILLING: A JOHNSON-COOK'S CONSTITUTIVE LAW ANALYSIS HA Kishawy, L Pang, TI El-WardanyInternational Journal of Materials Engineering and Technology 1 (2), 171 - 190, 2009 |
2 | 2009 |
CONTROL OF HOT SPOTS FOR CONTINUOUS MICROWAVE IRON MAKING – EFFECTS OF ORE-CARBON MIXTURE ROTATIONS ON REFRACTORY AND PIG IRON PRODUCTION – M Yanagawa, K Kashimura, M Hayashi, M Sato, T Mitani, N Shinohara, ...International Journal of Materials Engineering and Technology 9 (2), 119 - 134, 2013 |
2 | 2013 |
INTERDIFFUSION COEFFICIENTS OF BINARY MULTIPHASE SYSTEMS WITH CONSIDERATION OF VARIATION IN MOLAR VOLUMES JF Li, PA Agyakwa, CM JohnsonInternational Journal of Materials Engineering and Technology 12 (1), 25 - 36, 2014 |
2 | 2014 |
USE OF SPONGE-GOURD (Luffa cylindrica) AGRO-RESIDUE AS FILLER FOR RENEWABLE HIGH DENSITY POLYETHYLENE: DEVELOPMENT AND CHARACTERIZATION OF COMPOSITES VA Escócio, EBAV Pacheco, AMF de Sousa, A de P. Cavalcante, ...International Journal of Materials Engineering and Technology 12 (2), 151 - 176, 2014 |
2 | 2014 |
AN EFFICIENT NANOPARTICLES- GAS SENSOR FOR INDUSTRIAL APPLICATIONS P Yoboue, A Konaté, O Asseu, P Tety, P MéniniInternational Journal of Materials Engineering and Technology 11 (1), 41 - 56, 2014 |
2 | 2014 |
THE USE OF EXPERIMENTAL DESIGN IN THE EVALUATION OF MECHANICAL PROPERTIES OF PP/VERMICULITE COMPOSITES EAF Araújo, ÉBAV Pacheco, LLY Visconte, ALN da Silva, L SirelliInternational Journal of Materials Engineering and Technology 13 (2), 219 - 232, 2015 |
2 | 2015 |
PHOTODISCOLORATION PROCESSES OF DYES REACTIVE USING RADIATION AND Fe/TiO2 LMS Colpini, GG Lenzi, RCT de Souza, MB Urio, DM Kochepka, ...International Journal of Materials Engineering and Technology 14 (4), 189 - 204, 2016 |
2 | 2016 |
MICROSTRUCTURAL CHARACTERIZATION AND NUMERICAL MODELING OF HEAT AND FLUID FLOW DURING SOLIDIFICATION OF ALUMINIUM ALLOY CP Egole, HE Mgbemere, GI Lawal, GC NzebukaInternational Journal of Materials Engineering and Technology 17 (1), 21 - 77, 2018 |
2 | 2018 |
DRY SLIDING WEAR BEHAVIOR OF GRAPHITE FILLED POLYAMIDE66 COMPOSITE MATERIAL CL Srinivas, MMM Sarcar, KNS Suman, KR PrakashInternational Journal of Materials Engineering and Technology 10 (1), 9 - 18, 2013 |
2 | 2013 |
ALUMINIUM ALLOYS: A SURVEY OF DATA IN THE LITERATURE DK SukerInternational Journal of Materials Engineering and Technology 9 (1), 1 - 18, 2013 |
1 | 2013 |
EFFECTS OF MACHINING PARAMETERS IN TURNING ON ROUNDNESS ERROR OF MACHINED COMPONENTS YA Hadi, S Varghese, AA IbrahimInternational Journal of Materials Engineering and Technology 2 (1), 55 - 68, 2009 |
1 | 2009 |
APPLICATION OF FUNCTIONAL GRADIENT AL METAL MATRIX COMPOSITE AS A BRAKE ROTOR-FINITE ELEMENT ANALYSIS H Zhang, A Loukus, J LoukusInternational Journal of Materials Engineering and Technology 3 (2), 143 - 153, 2010 |
1 | 2010 |
FAILURE ANALYSIS OF 316L STAINLESS STEEL SEAMLESS TUBE KM Hafez, M RamadanInternational Journal of Materials Engineering and Technology 8 (1), 27 - 35, 2012 |
1 | 2012 |
DETERMINATION OF FRICTION COEFFICIENT IN SHEET METAL FORMing THROUGH BENDING UNDER TENSION TEST LF Folle, JL Ferrarini, L SchaefferInternational Journal of Materials Engineering and Technology 8 (1), 37 - 48, 2012 |
1 | 2012 |
SYNTHESIS AND CHARACTERIZATION OF FUNCTIONALIZED CARBON NANOTUBES EMPLOYING COBALT NITRATE AND ACETONE BY USING SPRAY PYROLYSIS DEPOSITION TECHNIQUE JA Gómez, A Marquez, M Avalos-Borja, A Pérez, A Duarte-Moller, ...International Journal of Materials Engineering and Technology 8 (2), 155 - 169, 2012 |
1 | 2012 |
NANOLEAD-FREE SOLDER ALLOYS FOR ELECTRONIC PACKAGING AND INTEGRATION AE Hammad, S El-MollaInternational Journal of Materials Engineering and Technology 15 (1), 23 - 62, 2016 |
1 | 2016 |
A NUMERICAL METHOD FOR THE INVESTIGATION OF DOPING AND CODOPING EFFECT ON MASS TRANSPORT BY SURFACE DIFFUSION IN A GRANULAR PACKING H Tossoukpè, J Bruchon, F Valdivieso, S DrapierInternational Journal of Materials Engineering and Technology 11 (2), 73 - 100, 2014 |
1 | 2014 |
OPTICALLY CLEAR THIN FILMS FOR REDUCTION OF EARLY STAGE BIOFOULING J Chapman, R Brown, S Russell, E Kitteringham, LL Nor, F ReganInternational Journal of Materials Engineering and Technology 12 (1), 1 - 23, 2014 |
1 | 2014 |
ANALYSIS OF BUCKLING BEHAVIOR OF ELLIPTICAL PLATE WITH NON-CONCENTRIC ELLIPTIC HOLE S Sanusei, E Mazhari, A ShahidiInternational Journal of Materials Engineering and Technology 13 (1), 81 - 108, 2015 |
1 | 2015 |
TECHNOLOGY FOR MACHINING OF Bi4Ge3O12 SCINTILLATOR CRYSTALS APPLICABLE IN-HOUSE G GenovInternational Journal of Materials Engineering and Technology 14 (1), 67 - 78, 2015 |
1 | 2015 |
DIFFUSION PROCESS IN REVERBERATORY FURNACE TO CONTROL THE QUALITY OF RECYCLED ALUMINUM W SupraptoInternational Journal of Materials Engineering and Technology 15 (4), 205 - 223, 2016 |
1 | 2016 |
THE EFFECTS OF THE NiO AND SiO_2 THIN FILMS ON THE POROUS SILICON OPTICAL AND CHEMICAL STABILITY S Thamri, M Ouadhour, M Jlassi, M Hajji, H EzzaouiaInternational Journal of Materials Engineering and Technology 15 (2-3), 171 …, 2016 |
1 | 2016 |
COMPARATIVE COOKING TESTS OF TWO PARABOLIC AND ELLIPTICAL SOLAR CONCENTRATORS AT COVERED FIREPLACES LOCATED IN A GREENHOUSE AREA D Soro, S Modibo, T Siaka, B MarÃ, B AkaInternational Journal of Materials Engineering and Technology 18 (2), 67 - 89, 2019 |
1 | 2019 |
COMPARATIVE COOKING TESTS OF TWO PARABOLIC AND ELLIPTICAL SOLAR CONCENTRATORS AT COVERED FIREPLACES LOCATED IN A GREENHOUSE AREA D Soro, S Modibo, T Siaka, B MarÃ, B AkaInternational Journal of Materials Engineering and Technology 18 (2), 67 - 89, 2019 |
1 | 2019 |